Newport XPS-D Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 58

background image

XPS-D Controller

Start-Up Manual

This procedure is for the Windows 7 operating system (almost similar process for

Windows 8):

•

Start Button > Control Panel > Network and Sharing Center => Change adapter

settings.

•

Right Click on Local Area Connection Icon and select Properties.

•

Highlight Internet Protocol Version 4 (TCP/IPv4) and click on Properties.

•

Verify Obtain an IP address automatically is selected and click "OK".

HOST Connection:

•

Proceed the same way but select “Use the following IP address” in the previous

screenshot.

•

Type “IP address: 192.168.0.100” and “Subnet mask: 255.255.255.0” for example

(assuming the HOST IP address is still at the original value 192.168.0.254) and click

"

OK

".

EDH0395En1031 – 09/18

18

«
...
24
25
26
27
28
...
»

Содержание XPS-D



























































Отзывы:

Нет отзывов

Похожие инструкции для XPS-D

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

CITY ELITE SINGLE

Бренд: Baby Jogger Страницы: 3

Бренд: Baccara Страницы: 16

Бренд: BABYSTYLE Страницы: 8

Бренд: BABYSTYLE Страницы: 32

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: Fantech Страницы: 2

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: Balboa Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды