Newport XPS-D Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 58

background image

XPS-D Controller

Start-Up Manual

•

Do not open the XPS Controller/Driver stand-alone motion controller. There are no

user-serviceable parts inside the XPS Controller/Driver.

•

Return equipment to Newport Corporation for service and repair.

•

Dangerous voltages associated with the power supply are present inside

Controller/Driver unit. To avoid injury, do not touch exposed connections or

components while power is on.

•

Follow precautions for static-sensitive devices when handling electronic circuits.

WARNING

This product is equipped with a 3-wire grounding type plug. Any

interruption of the grounding connection can create an electric shock

hazard. If you are unable to insert the plug into your wall plug

receptacle, contact an electrician to perform the necessary alterations

to ensure that the green (green-yellow) wire is attached to earth

ground.
System earthing must be of type earthed neutral (TN-) as defined by

CEI60364.

EDH0395En1031 – 09/18

4

«
...
10
11
12
13
14
...
»

Содержание XPS-D



























































Отзывы:

Нет отзывов

Похожие инструкции для XPS-D

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: Savant Страницы: 2

Бренд: tell Страницы: 11

Бренд: Altronix Страницы: 8

Бренд: nvent Страницы: 6

Бренд: Smart Vision Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды