Newave PowerValue 11 Скачать руководство пользователя страница 15

Страница: 15 / 44

Newave_OPM_PV11_PV31 _GB_250805.doc Installation

Page 15

Under the connection terminal of the UPS there is a cable-fixing rail to ensure that the cables have
been fastened properly

3.6.16 Connection of the Mains Supply

After the UPS has been unpacked and brought to its final position the authorized technician may start
with the cabling.

ALL THE OPERATIONS IN THIS MANUAL MUST BE PERFORMED BY AUTHORISED
ELECTRICIANS OR BY QUALIFIED INTERNAL PERSONNEL.

To ensure protection of the personnel during the installation of the UPS make sure that the
connections are performed under the following conditions:

•

No mains voltage is present;

•

All loads are shut down and disconnected;

•

UPS PowerValue

is shut down and voltage-free.

Remove the terminal cover of the UPS

Before connecting the input power cables make sure that:

•

UPS-System is placed in its correct position;

•

Maintenance Bypass IA1 is open in position OFF;

Connect the input power cable coming from the LV-Distribution Board to the terminals of the UPS in
accordance with Figures 2 and 3.

NOTE: Neutral input wire must always be connected!

NOTE: The UPS PowerValue

is provided with facilities for both single feed (one common input

cable for rectifier and bypass) and dual feed (two separate input cables for rectifier and bypass
respectively).
The standard UPS PowerValue

is always supplied with facilities for a single feed. If dual feed

is required please contact next Service Centre

3.6.17 Single Input Feed

To achieve correct Input Cabling see Drawing in see Figures 3.

For single input feed connect the mains input cable to UPS Terminal Block according to the following
table:

For minimum recommended Input Cable Sections and Fuse Ratings for the PowerValue

see table in

Section Technical Specifications at the end of this User Manual.

Under the connection terminal of the UPS there is a cable-fixing rail to ensure that the cables have
been fastened properly.

3.6.18 Dual Input Feed

NOTE

: In the standard version PowerValue

comes with SINGLE INPUT FEED. If DUAL

INPUT FEED is required please contact your next service office before performing any cabling.

MAINS INPUT CABLE

UPS TERMINAL

Phase L1

1L1

Phase L2

1L2

Phase L3

1L3

NEUTRAL 1N
EARTH PE

Содержание PowerValue 11













































Результаты поиска

Содержание PowerValue 11

Отзывы:

Бренды по названию

Популярные бренды

Newave PowerValue 11, Руководство пользователя

Результаты поиска

Содержание PowerValue 11

Отзывы:

Бренды по названию

Популярные бренды