Ness Auto IP NVR Скачать руководство пользователя страница 61

Страница: 61 / 94

OSD Setup Manual

•

Then click on the <Menu> icon and go to

<Event Setup>

<Per

Channel

Config>

<CH 1>

<Detection Config>

. Note that users

have to select the correct corresponding channel number.

•

Click on the

<Connect to camera>

button and the webpage of the IP

camera will be opened up.

•

Then follow the User’s Manual for the IP camera to configure the motion

detection related setting.

Alarm In

This item allows users to enable / disable alarm input detection. According to

the application, select

<N/O>

(Normal Open) or

<N/C>

(Normal Close) to

enable the alarm input detection or select

<OFF>

to disable the detection.

If users set this item to

<N/C>

but no device is installed, the alarm will be

triggered and the Event Icon will always be displayed on the screen until this

item is changed to

<N/O>

<OFF>

or a device is installed to the unit.

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды

Ness Auto IP NVR, Руководство по установке

Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды