Ness Auto IP NVR Скачать руководство пользователя страница 56

Страница: 56 / 94

Manual

Event Setup

This menu allows users to determine behaviors of the Ness Auto IP NVR in response to

alarm events. In the Main menu, select

<Event>

and press ENTER. The following menu is

displayed. Items in the Event menu are described in the following subsections.

Event

Internal Buzzer
Event Icon
Email Notice
Email Attachment
SMS Setup
Alert Notification Setup
Event Full Screen
Event Duration
Per Channel Config

On
On
Off
Off

None

10 Sec

< Internal Buzzer >

This item allows users to enable / disable internal buzzer of the Premium H.264 NVR. If set

<On>

, the buzzer is activated in response to an alarm. If set to

<Off>

, the buzzer is not

activated.

< Event Icon >

The item enables (On) / disables (Off) the display of Event Icon on the main monitor when

an alarm event occurs. The event types are represented by a letter respectively; the

descriptions are as below table.

Event Type

Description

Alarm In event

Motion detection event

Video loss event

< Email Notice >

The item enables (On) / disables (Off) the Email notification of an event. When an alarm

event is triggered and

<Email Notice>

is enabled, an e-mail concerning the alarm event

will be sent.

NOTE: In order to send an event notification e-mail successfully, ensure that the unit

connects to the internet.

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Ness Auto IP NVR, Руководство по установке, Страница: 56 / 94

Результаты поиска

Содержание Auto IP NVR

Отзывы: