Ness Auto IP NVR Скачать руководство пользователя страница 60

Страница: 60 / 94

Manual

< Per Channel Config >

This menu is used to configure the event related settings for each channel. The menu is

displayed as below.

Per Channel Config

Channel Select
Video Loss Detect
Motion Detect
Detection Config
Alarm In
Alarm Out
Event Trigger Preset
Copy Event Settings

CH01

On
On

OFF

None

OFF

Channel Select

The item is used to select a desired channel for setting the parameters. Move

the cursor to

<Channel Select>

and press ENTER, then select a channel

using UP / DOWN keys. Press ENTER again to confirm the setting.

Video Loss Detect

This item allows users to enable / disable Video Loss acknowledged as an

alarm event. Select

<On>

to enable Video Loss acknowledged as alarm

events,

<Off>

to disable.

Motion Detect

Select

<On>

to enable the motion detection function of the Premium H.264

NVR. The motion detection related setting have to be setup by accessing the

IP camera’s webpage.

NOTE: The port forwarding function in <PoE Setup>

<Advance PoE

PnP Setting> menu have to be enabled.

Detection Config

This item is for connection to the webpage of the IP camera in order to

configure the motion detection related setting. However, it is unavailable here.

It will only be available in the remote monitoring software.

Follow steps below to access the webpage of the IP camera.

•

First connect the NVR at a PC via the remote monitoring software.

•

Enter authorized account name and password in order to access the OSD

menu.

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды

Ness Auto IP NVR, Руководство по установке

Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды