Ness Auto IP NVR Скачать руководство пользователя страница 48

Страница: 48 / 94

Manual

< Status >

After activating the IP camera, the

<Status>

item will be shown. Enter this item to see the

current status of the IP camera.

Status

Model
Streaming Format
Resolution
PPS
Bandwidth
Pkg. lost rate

ONVIF

H264(MP)

1280×720

30.00

511.37 KB/Sec

0.00%

Under the

<Status>

menu, the user will be able to see the model, streaming format,

resolution, PPS, bandwidth, and package lost rate of the IP camera. The information is

“read only”.

NOTE: The streaming format will show “MP” (main profile) or “BL” (base line)

according to the compression of the IP camera. The main profile has higher

compression technology.

< Copy Settings >

This item allows users to copy the settings of the current selected IP camera to any other

connected IP cameras. Enter this menu and select one or more target IP cameras. Then

select

<Confirm>

to apply the settings.

Copy Settings

COPY TO:

01 02 03 04 05 06 07 08

Select All Deselect All Confirm Cancel

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды

Ness Auto IP NVR, Руководство по установке

Результаты поиска

Содержание Auto IP NVR

Отзывы:

Бренды по названию

Популярные бренды