Ness Auto IP NVR Скачать руководство пользователя

Страница: 45 / 94

OSD Setup Manual

•

First set

<Dual Streaming Support>

<Yes>

and continue to the rest of

the setting.

•

If users wish to record the dual stream, choose <Yes> next to

<Dual

Streaming Recording>

•

The remaining items are the same as in <Main Stream Setup>. Choose

streaming format from

<H264>

<MJPEG>

, or

<MPEG4>

•

If users will setup streaming index, port, and protocol manually, set

<Adv.

Dual Streaming Options>

<On>

and select preferred values from the

corresponding menu items.

•

Otherwise, keep

<Adv. Dual Streaming Options>

<Off>

and the NVR

will take care of the setting.

IP Dome Protocol

If the connected device is an IP Dome Camera, then select an appropriate IP

Dome Protocol from the provided options.

IP Dome ID

If the connected device is an IP Dome Camera, then select an appropriate IP

Dome ID from the provided options.

< Device Setup >

Enter this item to set the basic settings of the IP camera. Upon entering this item, the

following message will be displayed.

Collecting data

Please wait!

If the connection cannot be detected, the following message will be displayed. Please

check the

<Hostname/IP>

, and

<Connection Setup>

again to make sure the settings are

correct.

Cannot get config from the IP device

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Похожие инструкции для Auto IP NVR

Бренды по названию

Популярные бренды

Ness Auto IP NVR, Руководство по установке

Результаты поиска

Содержание Auto IP NVR

Отзывы:

Похожие инструкции для Auto IP NVR

Бренды по названию

Популярные бренды