Ness Auto IP NVR Скачать руководство пользователя

Страница: 40 / 94

Manual

Monitor Setup

The NVR supports dual main monitor output, when simultaneous output function is off. To

configure the monitor settings, select

<Monitor>

from the Main menu and press ENTER.

Monitor

Show Camera Name
Monitor Brightness
Monitor Contrast
Monitor Chrominance
OSD Transparency
VGA Resolution
Show Color Bar
Mouse Sensitivity

Yes

0
0
0

720P

100%

< Show Camera Name >

This item allows users to choose whether to display the camera name on the screen. The

default is

<Yes>

, which displays the camera names with the video.

< Monitor Brightness >

The function allows users to adjust the brightness of the monitor. Move the cursor to the

item then press ENTER, and use UP / DOWN keys to adjust the numeric value. The range

of brightness values is

<-32>

<31>

< Monitor Contrast >

The item is used to adjust the color contrast of the monitor. The range of contrast values is

<-32>

<31>

< Monitor Chrominance >

Move the cursor to this item and press ENTER for adjusting the chrominance of the monitor.

Use UP / DOWN keys to adjust the numeric value. The range of chrominance values is

<-32>

<31>

Содержание Auto IP NVR































































































Результаты поиска

Содержание Auto IP NVR

Отзывы:

Похожие инструкции для Auto IP NVR

Бренды по названию

Популярные бренды

Ness Auto IP NVR, Руководство по установке

Результаты поиска

Содержание Auto IP NVR

Отзывы:

Похожие инструкции для Auto IP NVR

Бренды по названию

Популярные бренды