English
English
8
9
SELECTED PROGRAM VARIATION
Should it become necessary to select a
different program when a program is running,
you can simply press button (11). When the
new program is selected, the currently
running program will stop. The new program
will be active immediately with its own
execution times that will restart from the initial
values.
S W I TC H I N G F R O M AU T O M AT I C T O
MANUAL OPERATION
During the processing program, it is possible
to switch to manual mode at any time.
Holding down button (11) for 3 seconds
switches the machine to manual mode while
enabling the paddle LEDs (2a) and
compressor (1a).
The preservation cycle selected will be
deactivated.
TURNING OFF THE MACHINE DURING
AUTOMATIC OPERATION MODE
If you need to turn off the machine before the
completion of the active processing program,
you first need to switch to manual mode by
pressing and holding button (11) for 3
seconds and then pressing paddle (2) and
compressor (1) to stop any activity. Do not
act directly on the main switch (10)!
PRESERVATION CYCLE VARIATION WHILE
A PROGRAM IS RUNNING
During the preparation phase it is possible to
automatically vary the preservation cycle set
at any time. Repeatedly press button (12) until
the LED that corresponds to the desired cycle
is activated. The LED will flash for 3 seconds
a n d b e c o m e s s t e a d i l y l i t : t h e n e w
preservation cycle is selected at this point
and will be performed at the end of the
program. Each preparation program will
a c t i v a t e a t t h e e n d o f t h e s e l e c t e d
preservation cycle.
PADDLE LOCK UPON LID OPENING
The opening of the lid (3) only stops paddle
(5) and does not affect the preparation
program.
The closure of the lid (3) starts the motion of
the paddle (5) (where, at that time it is
provided by the selected program). If the
mixture proves excessively thick to prevent
the movement of the paddle, the machine will
automatically activate the previously selected
preservation cycle.
PADDLE SPEED ADJUSTMENT
The paddle rotation speed is adjustable by
means of the knob (8).
The adjustment of the paddle speed is
completely independent from the execution
of programs and can be changed at any time.
Air intake into the mixture varies according to
the recipe and paddle rotation speed.
To a lower number of revolutions corresponds
a higher density. (less air incorporated into the
ice cream). To a greater number of revolutions
corresponds a smaller density of the product
(more air incorporated into the ice cream)
We recommend you use low speeds when
preparing classic Italian gelato, Granita and
sorbet, and high speeds when preparing
semi-soft Italian gelato.
AUTOMATIC PRESERVATION
There are 4 preservation cycles available for
every whipping program (total of 16 cycles)
devised to meet a wide range of needs.
•In automatic mode, if the machine is not
stopped, at the end of each production
cycle is enabled the ice cream preservation
cycle selected.
•The activation of the preservation function is
i n d i c a t e d b y f l a s h i n g o f t h e L E D
corresponding to the processing program
of the ice cream selected.
•The desired cycle selection can take place
either at the beginning or during the
processing phase.
•Depending on the type of recipe and/or the
quantity prepared, every set of preservation
cycles combined with paddle speed
enables keeping gelato, Granita and sorbet
or other whipped products at the desired
conditions.
•Pressing the button (12) several times
causes the selection LEDs of the various
preservation cycles to light up in sequence.
If you switch from the first (LED (12a) active)
to the fourth (LED (12d) active) preservation
program, the density of gelato increases
production program. The LED (12a) will turn
on.
•Should you need to run a preservation cycle
related to a different production program,
before switching from manual mode to
preservation mode, select the desired
p r o d u c t i o n p r o g r a m ( s e e s e c t i o n
" C H A N G I N G T H E P R E S E R V AT I O N
CYCLE").
AUTOMATIC MODE
The
machine has a series
GELATO 15K CREA
of programs which automate the production
and preservation process.
•Follow the steps described in the section
"DIRECTIONS FOR USE".
•Press button (11) to start up the machine in
automatic mode by selecting the first
operation program. The LED flashes for 3
seconds during which, if you keep on
pressing the button (11), you will be able to
select other programs in sequence.
•When the LED becomes steadily lit, the
associated program starts up and begins
the production cycle.
•The machine has 4 production programs
and 4 preservation cycles for each of them.
When the program selected starts up you
can choose the preservation cycle desired.
Chose the preservation cycle by pressing
the button (12) repeatedly. When switching
from the first preservation program to the
fourth, gelato consistency increases
gradually.
•When the ice cream reaches the right
consistency, the production program stops
automatically and the preset preservation
cycle is enabled.
•Every production program has a preset
threshold time after which the machine
enters in preservation cycle, regardless of
the current production phase.
•If deemed appropriate, it is possible to
enable the selected preservation cycle at
any time , ending the production program.
Select the preservation cycle desired via the
key 12 (sequence selection). Keep the
paddle button (2) an compressor button (1)
pressed simultaneously for 3 seconds. The
machine will immediately switch from
production cycle to preservation cycle.
•CLASSIC ITALIAN GELATO AND SORBET
PROGRAM. By pressing button (11) once,
the LED (11a) will light up and activate the
production program. At the end of the
production cycle, the LED (11a) flashes
indicating that the selected preservation
cycle has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
locks. The preservation function is
automatically activated.
•
. By
SEMI-SOFT GELATO PROGRAM
pressing button (11) twice, LED (11b) will
light up and activate the processing
program. At the end of the production cycle,
the LED (11b) flashes indicating that the
selected preservation cycle has been
activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
locks. The preservation function is
automatically activated.
•
. By pressing button
GRANITA PROGRAM
(11) three times causes LED (11c) to light up
and activate Granita processing. At the end
of the production cycle, the LED (11c)
flashes indicating that the selected
preservation cycle has been activated.
If the preparation was ready before reaching
the operation time limit, the whipping paddle
locks. The preservation function is
automatically activated.
•
Pressing
FAST COOLING PROGRAM.
button (11) four times causes LED (11d) to
light up and activate the fast cooling
program. At the end of the production cycle,
the LED (11d) flashes indicating that the
selected preservation cycle has been
activated.
This program is used when processing
mixtures with high initial temperatures. The
p r o g r a m q u i c k l y b r i n g s d o w n t h e
temperature without adding too much air
into the mixture, saving time and improving
the quality of the ice cream made.
