Neco STIR-RITE III Скачать руководство пользователя страница 41

Страница: 41 / 60

Attach the Main Disconnect Switch

to the Roof Inside

the Man-Hatch Opening.

Make Sure there is Clearance

for Stir-Rite III Movement.

If drilling is required, make sure to

properly seal the holes.

Shown as

Reference Only

Figure 51 - Install Electrical Main Disconnect

•

Do Not enter the bin unless power to all of the

equipment has been shut-off and locked out.

Failure to heed this warning could result in

severe personal injury or death!

WARNING

•

A main power disconnect switch capable of

being locked in only the OFF position shall be

provided. This shall be locked any time work is

being done on the equipment.

WARNING

Suspension Chain

(if necessary)

Suspension Chain

(if necessary)

Electrical Power-In

Cord

Safety

Chain

PHASE

VOLTS

# OF DOWN

AUGERS

MAIN DISCONNECT

AMPERAGE REQ’D

230

1 - 2

30 AMP

230

3 - 4

60 AMP

230

1 - 4

30 AMP

460

1 - 4

15 AMP

•

Leave the disconnect switch in the OFF

position until all installation is complete,

and while there is any person still in the

bin. Entanglement with augers can cause

severe personal injury or death!

WARNING

Содержание STIR-RITE III





























































Результаты поиска

Содержание STIR-RITE III

Отзывы:

Бренды по названию

Популярные бренды

Neco STIR-RITE III, Руководство владельца/оператора

Результаты поиска

Содержание STIR-RITE III

Отзывы:

Бренды по названию

Популярные бренды