NEC MuPD78F0132H Скачать руководство пользователя страница 245

Страница: 245 / 540

CHAPTER 11 CLOCK OUTPUT/BUZZER OUTPUT CONTROLLER

User’s Manual U16899EJ2V0UD

245

(2) Port mode register 14 (PM14)

This register sets port 14 input/output in 1-bit units.

When using the P140/INTP6/PCL pin for clock output and the P141/INTP7/BUZ pin for buzzer output, set

PM140, PM141 and the output latch of P140, P141 to 0.

PM14 is set by a 1-bit or 8-bit memory manipulation instruction.

RESET input sets PM14 to FFH.

Figure 11-3. Format of Port Mode Register 14 (PM14)

Address: FF2EH After reset: FFH R/W

Symbol

7 6 5 4 3 2 1 0

PM14 1 1 1 1 1 1

PM141

PM140

PM14n

P14n pin I/O mode selection (n = 0, 1)

Output mode (output buffer on)

Input mode (output buffer off)

11.4 Clock Output/Buzzer Output Controller Operations

11.4.1 Clock output operation

The clock pulse is output as the following procedure.

<1> Select the clock pulse output frequency with bits 0 to 3 (CCS0 to CCS3) of the clock output selection register

(CKS) (clock pulse output in disabled status).

<2> Set bit 4 (CLOE) of CKS to 1 to enable clock output.

Remark The clock output controller is designed not to output pulses with a small width during output

enable/disable switching of the clock output. As shown in Figure 11-4, be sure to start output from the

low period of the clock (marked with * in the figure). When stopping output, do so after securing high

level of the clock.

Figure 11-4. Remote Control Output Application Example

CLOE

Clock output

11.4.2 Operation as buzzer output

The buzzer frequency is output as the following procedure.

<1> Select the buzzer output frequency with bits 5 and 6 (BCS0, BCS1) of the clock output selection register

(CKS) (buzzer output in disabled status).

<2> Set bit 7 (BZOE) of CKS to 1 to enable buzzer output.

Содержание MuPD78F0132H





























































































































































































































































































































































































































































































































































Результаты поиска

Содержание MuPD78F0132H

Отзывы:

Похожие инструкции для MuPD78F0132H

Бренды по названию

Популярные бренды

NEC MuPD78F0132H, Руководство пользователя

Результаты поиска

Содержание MuPD78F0132H

Отзывы:

Похожие инструкции для MuPD78F0132H

Бренды по названию

Популярные бренды