NEC Express5800/120Eg Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 332

NEC Express5800/120Eg Скачать руководство пользователя страница 99

Configuring Your Server 4-31

You are offered the following options:

Format Disk

—Simulates a low-level format of the hard drive by writing zeros to the

entire disk. Serial ATA drives are low-level formatted at the factory and do not need to be
low-level formatted again.

IMPORTANT:

Formatting destroys all data on the drive. Be sure to

back up your data before performing this operation.

Verify Disk Media

—Scans the media of a disk drive for defects.

ADD-IN CARD'S BIOS

Refer to the documentation coming with the optional add-in card for details.

When the server has multiple optional PCI boards installed, the server first displays the start-up
message of the BIOS SETUP Utility of the mother board.    It then displays the utility start-up
message for optional PCI boards one by one.    The start-up message appears for the optional PCI
board in the PCI #1 slot first, then PCI #2, PCI #3, PCI #4, and finally PCI #5.    The message
displayed may vary depending on the optional PCI board.    Refer to the manual that comes with the
optional PCI board for details.

«
...
97
98
99
100
101
...
»

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов