NEC Express5800/120Eg Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 332

NEC Express5800/120Eg Скачать руководство пользователя страница 45

General Description 2-17

NEC ESMPRO

The NEC ESMPRO is server management software that runs on the OS. The NEC ESMPRO
includes the NEC ESMPRO Manager for the server monitoring terminal and the NEC ESMPRO
Agent for the NEC Express server.

NOTE:

For details of major functions of the NEC ESMPRO, system

configuration and setups with the NEC ESMPRO, see Chapter 6.
Available functions of the NEC ESMPRO depend on the OS you install.
Ask your sales agent for details.

Off-line Maintenance Utility

The Off-line Maintenance Utility is used for proactive maintenance and fault analysis of the server.
Normally this utility is used by the maintenance engineer.

Refer to Chapter 8 for details.

System Diagnostic Utility

The system diagnostic utility contained in the NEC EXPRESSBUILDER is useful to prevent the
hardware failures. See Chapter 7 for details.

«
...
43
44
45
46
47
...
»

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов