NEC Express5800/120Eg Скачать руководство пользователя страница 323

Страница: 323 / 332

Installing Windows 2000 F-13

Re-install the Network Driver

After installing OS and deleting the network drivers, if you want to re-install the network drivers,
follow the procedure below.

Restart OS and logon to your system.

[Upgrade Device Driver Wizard] dialog box appears.

Click [Next].

Confirm that the [Search for a suitable driver for my device (recommended)] radio button
is selected and click [Next].

Select the [Specify a location] check box and deselect other check boxes.

Click [Next].

Other [Upgrade Device Driver Wizard] dialog box opens.

When using [Intel(R) PRO/1000MT Network Connection], specify [<CD-ROM Drive
Letter>:\WINNT\W2K\BC3\PRO1000\WIN2K].

Then click [OK].

Click [Next].

Click [Finished].

After re-installing the network drivers, the link speed and Duplex mode need to be
specified.

Refer to "Network Driver" described earlier.

Graphics Accelerator Driver

Install the display driver using the following procedure.

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Run the "CD-ROM Drive Letter:\WINNT\W2K\VIDEO\SETUP.EXE".

Follow the message on the screen.

When the message "Digital Signature Not Found" message appears, click on [Yes].

Remove the NEC EXPRESSBUILDER CD-ROM and restart the system following a
message on the screen.

Содержание Express5800/120Eg













































































































































































































































































































































Результаты поиска

Содержание Express5800/120Eg

Отзывы:

NEC Express5800/120Eg, Руководство пользователя, Страница: 323 / 332

Результаты поиска

Содержание Express5800/120Eg

Отзывы: