Notes on Using Your Server 1-5
Installation, Relocation, Storage, and Connection
CAUTION
Never attempt to lift the server only by yourself.
Your server weighs max. 33 kg (depending on its hardware configuration).
Carrying the server only by yourself may strain your back. Hold the server
firmly by its bottom with at least three or more people. Do not hold the front
door to lift the server. The front door may be disengaged from the server,
causing personal injury.
Do not install the server in any place other than specified.
Do not install the server in the following places or any place other than specified
in this manual. Failure to follow this instruction may cause a fire.
■
a dusty place
■
a humid place such as near a boiler
■
a place exposed to direct sunlight
■
an unstable place
Do not use or store the server in corrosive environment.
Avoid the usage or storage of your server in an environment which may be
exposed to corrosive gases, such as those including but not limited to: sulfur
dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia and/or ozone.
Avoid installing your server in a dusty environment or one that may be exposed
to corrosive materials such as sodium chloride and/or sulfur.
Avoid installing your server in an environment which may have excessive metal
flakes or conductive particles in the air.
Such environments may cause corrosion or short circuits within your server,
resulting in not only damage to your server, but may even lead to be a fire
hazard.
If there are any concerns regarding the environment at the planned site of
installation or storage, please contact your sales representative.
Do not connect any interface cable with the power cord of the server plugged to
a power source.
Make sure to power off the server and unplug the power cord from a power
outlet before installing/removing any optional internal device or
connecting/disconnecting any interface cable to/from the server. If the server
is off-powered but its power cord is plugged to a power source, touching an
internal device, cable, or connector may cause an electric shock or a fire
resulted from a short circuit.
Do not use any unauthorized interface cable.
Use only interface cables provided by NEC and locate a proper device and
connector before connecting a cable. Using an authorized cable or connecting
a cable to an improper destination may cause a short circuit, resulting in a fire.
Also, observe the following notes on using and connecting an interface cable.
■
Do not use any damaged cable connector.
■
Do not step on the cable.
■
Do not place any object on the cable.
■
Do not use the server with loose cable connections.
Содержание Express5800/120Eg
