manualshive.com logo in svg

NEC Express5800/120Eg, Руководство пользователя, Страница: 320 / 332

Поделиться
Скачать
NEC Express5800/120Eg Скачать руководство пользователя страница 320

F-10  Installing Windows 2000

Updating the System - Installing Service Pack -

To ensure normal system operation you should update your system using the following procedures.

IMPORTANT:

 Be sure to confirm the following items before

applying Service Pack to your system.
This system does not support Windows 2000 Service Pack 1 - 3.
If you install Windows 2000 CD-ROM which contains Service Pack 4
to your system, you do not have to apply Service Pack 4 again.

 

1. 

Logon to the system using the administrator account or other account which is a member
of the Administrators group.

 

2. 

Insert the NEC EXPRESSBUILDER CD-ROM into the CD-ROM drive.

Master Control Menu is automatically appeared on the screen.

 

3. 

Click on [Setup] with left mouse button and click on [Update NEC Express5800 system]
section.

 

4. 

Continue your work for system update as the following message.

 

5. 

Click on [Restart Computer] to restart the system.

 

6. 

Remove the NEC EXPRESSBUILDER CD-ROM from the CD-ROM drive immediately
after clicking on [Restart Computer]

IMPORTANT:

 If you change the configuration of the system (by

adding or removing hardware or Operating system software
components) or repair the system, you must run the system update
again.

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов