manualshive.com logo in svg

NEC Express5800/120Eg, Руководство пользователя, Страница: 203 / 332

Поделиться
Скачать
NEC Express5800/120Eg Скачать руководство пользователя страница 203

Troubleshooting  8-21

Problems with NEC EXPRESSBUILDER

When the server is not booted from the NEC EXPRESSBUILDER CD-ROM, check the following:

T

Did you set the NEC EXPRESSBUILDER during POST and restart the server?

→

If you do not set the NEC EXPRESSBUILDER during POST and restart the
server, an error message will appear or the OS will boot.

T

Is BIOS configuration correct?

→

The boot device order may be specified with the BIOS SETUP utility of the server.
Use the BIOS SETUP utility to change the boot device order to boot the system
from the CD-ROM drive first.

<Menu to check:    [Boot]>

T

Is an error message appeared?

→

When an error occurs while the NEC EXPRESSBUILDER is in progress, the
following message appears. After this message appears, check the error and take
the appropriate corrective action according to the message listed in the table
below.

Message

Cause and Remedy

This machine is not supported.

This NEC EXPRESSBUILDER version is not
designed for this server.    Execute the NEC
EXPRESSBUILDER on the compliant server.

NvRAM access error

An access to the nonvolatile memory
(NvRAM) is not acceptable.

Hard disk access error

The hard disk is not connected or it is failed.
Check whether the hard disk is correctly
connected.

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов