NEC Express5800/120Eg Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 332

NEC Express5800/120Eg Скачать руководство пользователя страница 35

General Description 2-7

1

Power supply

The power unit supplies DC powers to the server.

2

AC inlet

The AC inlet is connected with the power cord.

3

Serial port B connector

The serial port B connector is used to connect the server to a device with the serial interface.
The server cannot be directly connected to a leased line through the connector.

4

Additional PCI board slots

Optional PCI boards may be inserted into the slots.

5

Mouse connector

The mouse connector is connected with the mouse coming with the server.

6

USB-1 (left) / USB-2 (right) connectors

The USB-1 and USB-2 connectors are connected with devices accepting the USB interface.

7

Keyboard connector

The keyboard connector is connected with keyboard coming with the server.

8

Monitor connector

The monitor connector is connected with the display unit.

9

Serial port A connector

The serial port A connector is connected with a device having the serial interface.

10

Maintenance LEDs

11

Link/ACT lamp

The Link/ACT lamp shows the LAN access status.

12

LAN connector

The LAN connector is connected with a network system on LAN (1000BASE-T/100BASE-
TX/10BASE-T).

13

1000/100/10 lamp

1000/100/10 lamp indicates the LAN transfer rate.

«
...
33
34
35
36
37
...
»

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов