manualshive.com logo in svg

NEC Express5800/120Eg, Руководство пользователя, Страница: 260 / 332

Поделиться
Скачать
NEC Express5800/120Eg Скачать руководство пользователя страница 260

10-4  Internal Cabling Diagrams

SCSI Hard Disk Drive Configuration

You need an optional SCSI controller and internal SCSI cable to install a SCSI hard disk drive or
file device.

Set SCSI IDs as shown in the figure below. Set the terminating resistor (Enabled/Disabled) for the
last-connected device in the SCSI chain. Set "Disabled" for all the middle devices. A terminating
connector may be installed depending on the internal SCSI cable. If the SCSI cable ends with a
terminating resistor, set "Disabled" for all the terminating resistors of connected devices. For the
settings, see the manual provided with each device.

A file device needs settings such as a SCSI transfer rate. For the transfer rate, see the manual
provided with the file device. Use the BIOS utility of the SCSI controller to make the settings. For
details, see the manual provided with the SCSI controller.

Mother board

Option
Option

CD-ROM

Option ID0

5.25-inch
device bay

Floppy
disk drive

Floppy disk drive cable

3.5-inch
disk bay

SATA cable

Terminator

Terminator

SCSI cable

Содержание Express5800/120Eg













































































































































































































































































































































Отзывы:

Нет отзывов