NEC 78K0S/KU1+ Скачать руководство пользователя страница 69

Страница: 69 / 324

CHAPTER 5 CLOCK GENERATORS

User’s Manual U18172EJ2V0UD

(3) Oscillation stabilization time select register (OSTS)

This register is used to select oscillation stabilization time of the clock supplied from the oscillator when the STOP

mode is released. The wait time set by OSTS is valid only when the crystal/ceramic oscillation clock is selected

as the system clock and after the STOP mode is released. If the high-speed internal oscillator or external clock

input is selected as the system clock source, no wait time elapses.

The system clock oscillator and the oscillation stabilization time that elapses after power application or release of

reset are selected by the option byte. For details, refer to

CHAPTER 15 OPTION BYTE

OSTS is set by using an 8-bit memory manipulation instruction.

Figure 5-5. Format of Oscillation Stabilization Time Select Register (OSTS)

Address: FFF4H, After reset: Undefined, R/W

Symbol

7 6 5 4 3 2 1 0

OSTS 0 0 0 0 0 0

OSTS1

OSTS0

OSTS1

OSTS0

Selection of oscillation stabilization time

0 0

(102.4

0 1

(409.6

1 0

(3.27 ms)

1 1

(13.1 ms)

Cautions 1. To set and then release the STOP mode, set the oscillation stabilization time as

follows.

Expected oscillation stabilization time of resonator

≤

Oscillation stabilization time

set by OSTS

2. The wait time after the STOP mode is released does not include the time from the

release of the STOP mode to the start of clock oscillation (“a” in the figure

below), regardless of whether STOP mode was released by reset signal

generation or interrupt generation.

STOP mode is released

Voltage

waveform

of X1 pin

3. The oscillation stabilization time that elapses on power application or after release

of reset is selected by the option byte. For details, refer to CHAPTER 15 OPTION

BYTE.

Remarks 1.

( ): f

= 10 MHz

Determine the oscillation stabilization time of the resonator by checking the

characteristics of the resonator to be used.

Содержание 78K0S/KU1+





































































































































































































































































































































Результаты поиска

Содержание 78K0S/KU1+

Отзывы:

Похожие инструкции для 78K0S/KU1+

Бренды по названию

Популярные бренды

NEC 78K0S/KU1+, Руководство пользователя

Результаты поиска

Содержание 78K0S/KU1+

Отзывы:

Похожие инструкции для 78K0S/KU1+

Бренды по названию

Популярные бренды