NDD easyone pro Скачать руководство пользователя страница 93

Страница: 93 / 188

EasyOne Pro™ / EasyOne Pro™ LAB

Quality Messages and Quality Grades

5.4 FRC Quality Messages

Message

Criterion

Recommended action

FRC(MBW) Warning:
Extrapolated volume
computation failed
(set to zero)!

The extrapolated volume could
not be calculated.

Contact service.

FRC(MBW) Warning:
Extrapolated volume
computation too
high (set to zero)!

The extrapolated volume (i.e., the
volume that would be washed out
after cancellation of the test) is
greater than 1 liter.

Do not stop too soon.

FRC(MBW) Warning:
Inspiratory leak!

Air entered from outside during
inspiration.

The end-inspiratory molar mass
deviates from the tracer gas molar
mass by more than 0.2 g/mol.
This is indicative of air drawn in
from outside during inspiration.

Check

FRC barriette™

: are valves

jammed or was the

FRC barri-

ette™

not been properly inserted?

Check position of

spirette™

and

of nose clip.

Ask patient to breathe calmly.

FRC(MBW) Warning:
In- or expiratory pres-
sure too high!

Pressure in sensor tube is too
high.

The pressure in the sensor tube
exceeds ±5 mbar; possible rea-
sons are:

1) Insufficient pressure at the O2
gas port.

2) Patient's breaths are too deep;
the respiratory resistance and
thus the pressure drop increase
from about 2 l/s.

Check O2 gas supply: Is the inlet
pressure 3 bar? Only minimal
pressure variations are allowed
during the test.

Is the patient's breathing too
deep/too fast?
Ask the patient to breathe within
the limits of ±1.5 l/s.

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 93 / 188

Результаты поиска

Содержание easyone pro

Отзывы: