NDD easyone pro Скачать руководство пользователя страница 89

Страница: 89 / 188

EasyOne Pro™ / EasyOne Pro™ LAB

Quality Messages and Quality Grades

Low Inspiratory Vol-
ume

Maneuver not
acceptable. Inspira-
tory volume too low

The inspiratory volume is smaller
than 85% FVC/VC/Predicted

Make sure to perform a full expira-
tion before the valve closes, and
then a full inhalation of test gas

Inspiratory Time Too
Long

Maneuver not
acceptable. Inspira-
tion time exceeds
the maximum of 4
seconds

Inspiratory time > 4 seconds

Inhale test gas faster

Sampling volume at
this position too
large

Sample volume not correctly
determined

Reduce sample volume

Difference Prepara-
tion and Maneuver

Test cannot be evalu-
ated; gas sensor sig-
nals do not pass QC
check, possibly due
to leaks

Reference gas measurement and
inspiratory gas measurements do
not match within 80 ppm. This
means that most probably there is
a leak in the DLCO hose

Check for leaks; check gas supply

Sampling volume at
maximum position

Test cannot be evalu-
ated; exhaled vol-
ume too small

Can happen when very small vol-
umes are exhaled

Collection bar is beyond rightmost
position

Activate „Automatically rejected
volume“

After the breath hold, do not
exhale too fast.

DLCO-Warning: High
inspiratory CO dur-
ing tidal breathing!

An increased CO level was
detected during the tidal breath-
ing phase.

Check the DLCO valve unit.

If the error occurs repeatedly then
please contact service.

Test error: # of
breaths

Test cannot be evalu-
ated; DLCO maneu-
ver cannot be
detected

Number of breaths during DLCO
expiration could not be detected

Perform the DLCO maneuver with
full effort

Message

Criterion

Recommended action

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 89 / 188

Результаты поиска

Содержание easyone pro

Отзывы: