NDD easyone pro Скачать руководство пользователя страница 106

Страница: 106 / 188

Hygiene, Cleaning, Maintenance, Disposal

106

EasyOne Pro™ / EasyOne Pro™ LAB

Calibration Check with DLCO Simulator

In the

Utilities

menu, click

Calibration check

, then select

DLCO simulator

The test procedure is the same as in a human test (

"CO Diffusing Capacity

(DLCO)"

on page 67). For correct handling of the DLCO simulator, please

read the manual of the simulator manufacturer.

Note

We strongly recommend using only DLCO simulators
manufactured by Hans Rudolph (DLCO Simulator, 5560
Series).

Also refer to the DLCO simulator operator manual or to the
training clip at www.ndd.ch.

As an alternative to checking calibration with a DLCO
simulator, the calibration can be checked with a test subject
(see

"Calibration Check with Test Subject"

on page 107).

Make sure the gas concentrations of the test gas AND the
Simulator Test Gas are entered correctly as shown in Fig.
8-13.

FRC Calibration Check

The American Thoracic Society (ATS) recommends that testing of biological
controls should be performed at least monthly.

For that purpose use a biological subject and the standard trending func-
tionality.

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 106 / 188

Результаты поиска

Содержание easyone pro

Отзывы: