NDD easyone pro Скачать руководство пользователя страница 132

Страница: 132 / 188

Specifications

132

EasyOne Pro™ / EasyOne Pro™ LAB

Predicted val-

ues (spirome-

try)

NHANES III, Knudson_83, Knudson_76, Crapo, Mor-

ris, Hsu, Dockery (Harvard), Polgar, Gutierrez

(Canada), Eigen, Pereira, Pereira 2006/2008, Pérez-

Padilla (PLATINO), Pérez Padilla (Mexico), Pérez

Padilla (Mexico, Ped.), Chile 2010, 1997, ERS (ECCS/

EGKS), Zapletal 1977, Zapletal 2003, Stanojevic 2009

(GLI), Quanjer 2012 (GLI), Rosenthal, Austria 1988,

Austria 1994, Sapaldia (Swiss), Roca (Spain, SEPAR),

Vilozni 2005, Falaschetti, Klement (Russia), Heden-

ström (Sweden), Gulsvik, (Norway), Berglund, Birath

(Sweden), Langhammer (Norway), Finnish, Nystad,

Hibbert, Gore, Crockett, Ethiopia, Asia 1-4, JRS 2001,

Fukuda Standard (see

"Predicted Values"

page 139)

Predicted val-

ues (lung

capacity and

DLCO)

Ayers, Burrows, Crapo, Goldman & Becklake, Knud-

son, McGrath & Thompson, Miller, Gutierrez (Canada),

Klement (Russia), NHANES, Polgar, ERS, Zapletal,

Roca, Hedenström, Gulsvik, Pereira 2008, Thompson

(see

"Predicted Values"

on page 139)

Operating

conditions

Temperature

5 to 40 °C (41 to 104 °F)
LAB: 10 to 40 °C
(50 to 104 °F)

Relative humidity

15% to 95%,
no condensation
LAB: 30% to 75%,
no condensation

Atmospheric pressure

700 to 1060 hPa

Storage/

transport

Temperature

-20 to 50 °C (-4 to +122 °F)

Relative humidity

5% to 95%, no

condensation

Atmospheric pressure

500 to 1060 hPa

Certifications

CE Declaration of conformity

Device classi-

fication

Protection class I

Type BF applied part
Furthermore the device is not intended to be used in
the presence of oxygen rich environments. However,
where the device contains oxygen rich environments,
it complies with applicable requirements for fire pre-
vention.

Operating

voltage range

100 to 240 V, 50 to 60 Hz

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 132 / 188

Результаты поиска

Содержание easyone pro

Отзывы: