manualshive.com logo in svg

NDD easyone pro, Руководство оператора, Страница: 72 / 188

Поделиться
Скачать
NDD easyone pro Скачать руководство пользователя страница 72

Performing a Test

72

EasyOne Pro™ / EasyOne Pro™ LAB

 

Note

Interpret these results with caution because different breath-
ing baselines are possible.

SVC before washout 

Relaxed tidal breathing until a stable breathing baseline is 
detected (indicated with a line in the VT-diagram representing 
the breathing baseline line). Then perform a full SVC maneu-
ver; after that continue with the FRC washout maneuver. Lung 
volume parameters will be calculated based on this linked 
SVC maneuver (data from an "external" SVC test will not be 
used).

Note

Perform the SVC maneuver according to ATS/ERS guidelines to 
ensure accurate results.

SVC after washout 

First perform an FRC washout maneuver. After the washout 
continue with relaxed tidal breathing until a stable breathing 
baseline is detected (indicated with a line in the VT-diagram 
representing the breathing baseline line). Then perform a full 
SVC maneuver. Lung volume parameters will be calculated 
based on this linked SVC maneuver (data from an "external" 
SVC test will not be used).

Note

Perform the SVC maneuver according to ATS/ERS guidelines to 
ensure accurate results.

Performing a Test

Note

The patient wears a nose clip during the measurement and the 
lips must seal around the mouthpiece to prevent ambient air 
from being inhaled.

Instruct the patient according to the displayed on-line messages. The 
messages depend on the mode settings "Automatic" or "Manual" and on 
the selected option "Linked SVC".

Attach the 

FRC barriette™

  (see 

"FRC Test (EasyOne Pro™ LAB only)" 

on 

page 71).

Select the patient (see 

"Selecting/Adding a Patient" 

on page 41).

Select the test with 

FRC

.

The FRC test acquisition screen appears.

Содержание easyone pro





























































































































































































Отзывы:

Нет отзывов