manualshive.com logo in svg

NDD easyone pro, Руководство оператора, Страница: 7 / 188

Поделиться
Скачать
NDD easyone pro Скачать руководство пользователя страница 7

 

EasyOne Pro™ / EasyOne Pro™ LAB

7

Introduction

that information pertinent to several chapters is given only once. 
Therefore, read the manual once in its entirety.

To ensure patient safety, the specified measuring accuracy, and 
interference-free operation, we recommend using only original 
accessories available through ndd. The user is responsible if using non-
ndd accessories.

ndd is responsible for the effects on safety, reliability, and performance 
of the device, only if

assembly operations, extensions, readjustments, modifications, or 
repairs are carried out by ndd or by ndd-authorized personnel

the device is used in accordance with the instructions given in this 
manual.

The warranty does not cover damage resulting from the use of unsuitable 
accessories and consumables from other manufacturers.

Always consult with ndd, if you intend to connect equipment not 
mentioned in this manual.

Components and accessories must comply with the applicable IEC 
60601 safety standards and/or the configured system must comply with 
the collateral standard IEC 60601-1-1 "Requirements for the safety of 
medical electrical systems".

The power cord must be an approved type acceptable to the authorities 
in the country where the equipment is used.

EasyOne Pro™ 

must not be exposed to low temperatures during storage 

and transport to avoid moisture condensation at the application site. 
Wait until all moisture has vaporized before using the device. Allow the 
device to reach room temperature before using it.

All publications are in conformity with the device specifications and 
standards on safety of electromedical equipment valid at the time of 
printing. All rights are reserved for devices, circuits, techniques, software 
programs, and names appearing in this manual.

The illustrations in this manual are only examples. They are not binding 
in any way.

No part of this manual may be reproduced without written permission 
from ndd.

©

 2012

 

ndd Medizintechnik AG, Technoparkstr. 1, CH-8005 Zürich, Switzer-

land

Содержание easyone pro





























































































































































































Отзывы:

Нет отзывов