NDD easyone pro Скачать руководство пользователя страница 31

Страница: 31 / 188

EasyOne Pro™ / EasyOne Pro™ LAB

Start-up and Initial Preparation



Connect the other end of the tube to the pressure relief valve



Open the main valve

of the gas cylinder completely.



Slowly open the pressure relief valve

and set the manometer

to a

secondary pressure of 3 bar.

Danger

Explosion Hazard—An FRC overpressure valve that opens at
5 bar, is integrated in the device. If you select a higher
secondary pressure, the overpressure valve will open and
gas will escape.

Note

Exchange the gas cylinder if the primary pressure drops
below 10 bar!

2.5 Connecting the Keyboard and the Mouse

EasyOne Pro™

is equipped with a touch screen display and can thus be

operated without a keyboard or a mouse. However, if you prefer working
with a keyboard and a mouse, connect them to a USB port

(

, Fig. 2-2).

2.6 Connecting the Printer

Depending on the printer used, connect it to one of the USB ports (

, Fig.

2-2) or to one of the LAN ports

Note

Preinstalled and compatible printer models (please contact
your ndd dealer to find out about other options):



HP Deskjet 6988

Fig. 2-13

Connection for tube from FRC gas cylinder

Содержание easyone pro





























































































































































































Результаты поиска

Содержание easyone pro

Отзывы:

NDD easyone pro, Руководство оператора, Страница: 31 / 188

Результаты поиска

Содержание easyone pro

Отзывы: