manualshive.com logo in svg

Nautel NV30LT-N, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Nautel NV30LT-N Скачать руководство пользователя страница 189

NV30LT-N OPERATIONS & MAINTENANCE MANUAL

OPERATING THE TRANSMITTER

VERSION 0.1  2015-03-01

PAGE 3.2.171

Enabling and Operating the Orban Audio Processor

This section describes how to configure, enable and operate the optional Orban audio processor after it 
is installed in your transmitter. You can interface with audio processor functionality locally, using the 
transmitter's front panel UI, or remotely, using the advanced user interface (AUI). The extent of the 
features available depends on which interface is used.

Configuring the Transmitter for the Orban Audio Processor - see page 3.2.172

Enabling the Orban Audio Processor for Preset Selection - see page 3.2.173

Selecting an Orban Audio Processor Preset - see page 3.2.176

NOTE

: Using the Orban Inside option requires the installation of an Orban audio processor card in your 

transmitter. If you had a pre-existing transmitter when you received your Orban Inside kit, verify that 
the Orban card has been installed in the transmitter according to the NVLT - Orban Inside Quick Guide 
(QG12001), provided with the Orban Inside kit. Refer to the Pre-installation and Installation Manuals 
for information on purchasing and installing this option.

NOTE

: This section contains frequent reference to Orban's Optimod-FM 5500 Digital Audio Processor 

Operating Manual (see the link below). The equipment covered in the 5500 manual uses the same 
Orban audio processor as in your transmitter. The 5500 manual provides detailed information on the 
audio processor's functionality. If a discrepancy exists between the operational instructions in the 
Orban manual and this document, the latter shall prevail as this document is specific to operation with 
an NV30LT-N transmitter. View the Orban Optimod-FM 5500 Digital Audio Processor Operating Manual 
online at:

ftp://ftp.orban.com/5500/Documentation/

(the version number referenced in this link is controlled by a third party and is subject to change without notice)

Содержание NV30LT-N



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды