manualshive.com logo in svg

Nautel NV30LT-N, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Nautel NV30LT-N Скачать руководство пользователя страница 87

NV30LT-N OPERATIONS & MAINTENANCE MANUAL

OPERATING THE TRANSMITTER

VERSION 0.1  2015-03-01

PAGE 3.2.69

Figure 3.2.49: Main Audio editing screens

Use the up and down buttons to locate the desired audio
source - 

AES

, 

MPX

, 

Analog L/R

 or 

Audio Player

, then

press the accept (checkmark) button to save the change.
Press the cancel (

X

) button to discard changes and return to

the previous menu.

Use the up and down buttons to locate the desired stereo
mode - 

Stereo

, 

Right Mono

, 

Left Mono

 or 

L+R Mono

then press the accept (checkmark) button to save the change.
Press the cancel (

X

) button to discard changes and return to

the previous menu. 

Use the up and down buttons to locate the desired 
preemphasis characteristic - 

0 us

, 

25 us

, 

50 us

 or 

75 us

, then

press the accept (checkmark) button to save the change. 
Press the cancel (

X

) button to discard changes and return to

the previous menu.

Use the up and down buttons to toggle between 

ON

 or 

OFF

,

then press the accept (checkmark) button to save the change.
Press the cancel (

X

) button to discard changes and return to

the previous menu. Default setting is OFF.

Use the up and down buttons to move the cursor to the 
desired audio input and then press the right button to enable
editing of the parameter. 

Figure 3.2.50 on page 3.2.70

shows all the editing screens for the 

Input Levels

 sub-menu.

Within any of the editing screens, use the up and down 
buttons to edit a parameter value, noting the minimum and
maximum limitations indicated at the bottom of the display.
When complete, press the accept (checkmark) button to save
the change. Press the cancel (

X

) button to discard changes

and return to the previous menu.

Use the up and down buttons to select 

File Playlist

 or

Stream 1

 through 

Stream 255

, then press the accept (check-

mark) button to save the change. Press the cancel (

X

) button

to discard changes and return to the previous menu.

Use the up and down buttons to select again adjust level 
between -20 and 10 dB (in 0.01 dB increments), then press
the accept (checkmark) button to save the change. Press the
cancel (

X

) button to discard changes and return to the 

previous menu

Содержание NV30LT-N



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды