manualshive.com logo in svg

Nautel NV30LT-N, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Nautel NV30LT-N Скачать руководство пользователя страница 93

NV30LT-N OPERATIONS & MAINTENANCE MANUAL

OPERATING THE TRANSMITTER

VERSION 0.1  2015-03-01

PAGE 3.2.75

Figure 3.2.58: RDS Settings editing screens (1 of 3)

Use the up and down buttons to select Select Internal, Ext.
ASCII, Ext. UECP, ASCII Over IP, or UECP Over IP, then press
the accept (checkmark) button to save the change. Press the
cancel (

X

) button to discard changes and return to the previ-

ous menu. Default setting is UECP.

NOTE

: 

For an ASCII Over IP data source, RDS information

should be sent to the IP address of the NV30LT-N, port 7005.

NOTE

: 

For title/artist functionality, the NV30LT-N 

supports the radiotext (RT) data type, using the UECP or Ext.
ASCII data source.

Use the up and down buttons to select ON or OFF, then press
the accept (checkmark) button to save the change. Press the
cancel (

X

) button to discard changes and return to the 

previous menu. Default setting is OFF.

Use the up and down buttons to select Select 150 bps,
300 bps, 600 bps, 1.2 kbps, 2.4 kbps, 4.8 kbps, 9.6 kbps,
19.2 kbps, 38.4 kbps, 57.6 kbps or 115.2 kbps, then press the
accept (checkmark) button to save the change. Press the 
cancel (

X

) button to discard changes and return to the 

previous menu. Default baud rate is 19.2 kbps.

Use the up and down buttons to select a level between 0 and
10% (in 0.1% increments), then press the accept (checkmark)
button to save the change. Press the cancel (

X

) button to 

discard changes and return to the previous menu. Default
level is 0.0%.

Use the up and down buttons to select a phase angle 
between 0 and 360 degrees (in 0.1 degree increments), then
press the accept (checkmark) button to save the change.
Press the cancel (

X

) button to discard changes and return to

the previous menu. Default level is 0.0 degrees.

Enter an 8-character name. Use the right and left arrows to
move the cursor to the desired character. Use the up and
down arrows to edit the character, then press the accept
(checkmark) button to save the change. Press the cancel (

X

)

button to discard changes and return to the previous menu.

Содержание NV30LT-N



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды