manualshive.com logo in svg

Nautel NV30LT-N, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Nautel NV30LT-N Скачать руководство пользователя страница 17

NV30LT-N OPERATIONS & MAINTENANCE MANUAL

DESCRIPTION

VERSION 0.1  2015-03-01

PAGE 3.1.9

2-Input, Final Reject Load Assembly

The 2-input, final reject load assemby (A13) provides a means to dissipate reject power from the final 
two stages of combining the 

20 kW Rej Ld Pwr

 output of the 20 kW combiners’ 3 dB hybrid coupler and 

the 

Final Rej Ld Pwr

 output of the 30 kW combiner’s 4.77 dB hybrid coupler. The reject load assembly 

contains power resistors to dissipate reject power. Cooling air for the 2-input, final reject load assembly 
is provided by fans B10 and B11. The control/monitor stage monitors the speed of the cooling fans and 
regulates the voltage being applied to them accordingly.

Reject power generated by the 20 kW combiner and the 30 kW final combiner is dissipated by resistors 
in the 2-input, final reject load assembly. Micro-strip transmission lines (on 2-input reject load PWB 
A13A1) in close proximity to the reject load signals induces true RF sample voltages of the reject power. 
These samples are peak detected and applied to the control/monitor stage via the reject load interface 
PWB (A28). The reject load interface PWB provides an interface between the ac-dc power stage’s Rej 
Fan Volts supply and the cooling fans. It also acts as the interface between the cooling fans’ Rej Fan 
Tach signals and the control/monitor stage.

Output Power Probe

See electrical schematic Figure SD-37. The output power probe (A15) monitors the transmitter's forward 
and reflected power and generates the Fwd Pwr Sample (A1J1) and Refld Pwr Sample (A2J1) signals 
applied to the control/monitor stage for protection and monitoring. RF monitor PWB A3 provides a 
nominal 3.8 V rms [at 30 kW] signal at A3J1, which is applied to the panel mount connector (W8J1) 
behind the front, hinged UI panel. This can be used with a modulation monitor or spectrum analyzer. RF 
sample PWBs A4 and A5 provide similar samples at A4J1 and A5J1. The sample at A4J1 is applied to 
exciter B (if used) for use by the remote AUI’s spectrum analyzer display. The sample at A5J1 is not used 
in this configuration. Dc reflected power sample PWB A6 provides a dc voltage representative of the 
reflected power sample, for use by the control/monitor stage.

Содержание NV30LT-N



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды