manualshive.com logo in svg

National Instruments CompactDAQ cDAQ-9185, Руководство пользователя

Поделиться
Скачать
National Instruments CompactDAQ cDAQ-9185 Скачать руководство пользователя страница 7

Contents

vi

|

ni.com

Chapter 2
Networking

Internal Ethernet Switch ...................................................................................................2-1

IEEE 802.1AS-2011 Precision Time Protocol .........................................................2-1
IEEE 802.1Q-2014 Rapid Spanning Tree Protocol (RSTP).....................................2-2
Chassis MAC Addresses...........................................................................................2-2

Topology Options .............................................................................................................2-3

Line Topology...........................................................................................................2-3
Ring Topology ..........................................................................................................2-4
Star Topology ...........................................................................................................2-4
Other Topologies ......................................................................................................2-5

External Switch Requirements..........................................................................................2-6

Chapter 3
Analog Input

Analog Input Triggering Signals ......................................................................................3-1
Analog Input Timing Signals............................................................................................3-1

AI Sample Clock Signal ...........................................................................................3-2

Routing the Sample Clock to an Output Terminal ...........................................3-2

AI Sample Clock Timebase Signal...........................................................................3-2
AI Convert Clock Signal Behavior For Analog Input Modules ...............................3-3

Scanned Modules..............................................................................................3-3
Simultaneous Sample-and-Hold Modules ........................................................3-3
Delta-Sigma Modules .......................................................................................3-3
Slow Sample Rate Modules..............................................................................3-4

AI Start Trigger Signal .............................................................................................3-5

Using a Digital Source......................................................................................3-5
Using an Analog Source ...................................................................................3-5
Using a Time Source.........................................................................................3-5
Routing AI Start Trigger to an Output Terminal ..............................................3-5

AI Reference Trigger Signal.....................................................................................3-6

Using a Digital Source......................................................................................3-6
Using an Analog Source ...................................................................................3-7
Routing the Reference Trigger Signal to an Output Terminal..........................3-7

AI Pause Trigger Signal............................................................................................3-7

Using a Digital Source......................................................................................3-7
Using an Analog Source ...................................................................................3-7

Analog Input Sync Pulse...................................................................................................3-8
Getting Started with AI Applications in Software............................................................3-8

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание CompactDAQ cDAQ-9185













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды