manualshive.com logo in svg

National Instruments CompactDAQ cDAQ-9185, Руководство пользователя

Поделиться
Скачать
National Instruments CompactDAQ cDAQ-9185 Скачать руководство пользователя страница 21

1-10

|

ni.com

Chapter 1

Getting Started with the cDAQ Chassis

power to all of the modules. The green POWER LED on the front panel identifies when the 
power input is in use. 

Complete the following steps to connect a power source to the cDAQ chassis.
1.

Make sure the power source is turned off.

2.

If connected, loosen the connector screw flanges and remove the power screw terminal 
connector plug from the cDAQ chassis. Figure 1-7 shows the terminal screws, which secure 
the wires in the screw terminals, and the connector screw flanges, which secure the 
connector plug on the front panel.

Figure 1-7.  

Power Screw Terminal Connector Plug

Caution

Do 

not

 tighten or loosen the terminal screws on the power connector while 

the power is on.

3.

Connect the positive lead of the power source to the V terminal of the power connector plug 
and tighten the terminal screw.

4.

Connect the negative lead of the power source to the C terminal of the power screw 
terminal connector plug and tighten the terminal screw.

5.

Install the power connector plug on the front panel of the cDAQ chassis and tighten the 
connector screw flanges.

6.

Turn on the external power source.

If the power source is connected to the power connector using long wiring with high DC 
resistance, the voltage at the power connector may be significantly lower than the specified 
voltage of the power source.

The C terminal is not connected to chassis ground. You can connect the C terminal to chassis 
ground externally. Refer to the 

Power Requirements

 section of the specifications document for 

your chassis for information about the power supply input range. Refer to the 

Safety Voltages

 

section of the specifications document for your chassis

 

for information about the maximum 

voltage from terminal to chassis ground.

1

V (Positive) Terminal Screw

2

C (Negative) Terminal Screw

3

Connector Screw Flanges

1

2

3

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание CompactDAQ cDAQ-9185













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды