MULTILIFT Ultima S Flex Скачать руководство пользователя страница 92

Страница: 92 / 196

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

Switch and signal light of hydraulic body locks

The body locks are opened by pressing the switch in the control unit. A burning lock signal

light on the control unit means that the body locks are not fully closed.

The signal light blinks if the lock hooks are between the open and closed positions.

When in traffic, no driving or tipping is to be commenced if the light is on. Remove the

element obstructing the locks, or if they are obstructed by the lock pocket in the container

frame beam, check that the container is correctly positioned on top of the hook device.

Function

Open body locks

Close body locks

LED comes on

LED off

LEDs

2GCC

Display

and LEDs

2GRC

LEDs

2GMR

Button

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды