MULTILIFT Ultima S Flex Скачать руководство пользователя страница 44

Страница: 44 / 196

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

SECURE

Check that the container is locked

- hydraulic or mechanical locks are closed.

- the middle/rear frame (= tipping lock) must be closed

(See. ”Loading a short container”, paragraph 2)

THE SIGNAL LIGHT OF THE CONTAINER LOCKING

must not be lit.

Lift the main cylinders / middle frame together with the rear frame to the

desired or maximum tipping angle

- move the

CONTROL LEVER

slowly backwards (2GCC)

- press

MAIN CYLINDERS BACK

button (2GMR and 2GRC)

- the indicator light

FRAME NOT DOWN

comes on as the middle frame is rising

from the subframe

- the container must not touch the rear bumper of the truck or the ground.

Move the

control lever

back

Second LED

comes on

Button

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды