MULTILIFT Ultima S Flex Скачать руководство пользователя страница 31

Страница: 31 / 196

Ultima S / SL Flex & Pro

3/2019

Hooklift Multilift Ultima S / SL Flex & Pro

User Manual

114060421

OPEN

Button

Second LED

comes on

Open the hydraulic body locks

- press the

BODY LOCK

button

LOCKS NOT CLOSED

signal light lit on the control unit when the locks are

open.

Open the mechanical or hydraulic front locks (optional).

Move the hook arm fully rearward position

- move the

CONTROL LEVER

to left and back (2GCC)

- press the

HOOK ARM BACK

button (2GMR and 2GRC)

- start at idle and increase the engine speed gradually.

Mechanical tipping lock will be opened in the rear position of the hook arm.

Move the

Two LEDs

Button

control lever

are on

to left and

back

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды