MULTILIFT Ultima S Flex Скачать руководство пользователя страница 150

Страница: 150 / 196

150

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

NOTE!

Do not touch pressurised hydraulics. Do not remove any

hydraulic components before the hooklift equipment has been

supported mechanically.

General

• Keep the hydraulic system clean.

• Keep the oil in a clean, locked space. When adding oil, use

a funnel which has a fine filter net.

• Keep funnels and containers free of dust.

• Always use clean towels or preferably high quality tissue.

• Before removing the hydraulic system components, clean the surrounding

areas carefully with steam or fat removal agent.

Checking the oil level

When the middle frame and the hook arm are in operating position, the oil level should be

in the middle of the sight glass.

Checking the return filter

Use a dirt indicator to check how dirty the return filter is. Replace the filter cartridge if the

indicator is in the red zone when the pump works and the oil is at operational temperature.

Checking the pressure filter

Check the condition of the pressure filter and clean it or renew the filter cartridge.

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды