MULTILIFT Ultima S Flex Скачать руководство пользователя страница 159

Страница: 159 / 196

159

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

Slide pads in middle frame

Slide pads in hook arm

Welding

Before welding, ensure the material to be welded, method and additives.

Contact Multilift service, if needed.

Welding may only be carried out by a trained welder.

Check from the truck user manual all the electrical connections which need to be

disconnected before welding. Remove the hooklift equipment electrical system connection

to the truck always before welding.

Connect the earthing cable as close as possible to the spot to be welded. If the welding

current flows through bearings, joints and seals, they might get damaged.

Check that the welding and flame cutting sparks do not fly to oily areas. Remember also

the protection of the truck cab.

Use always welding protections. Ensure sufficient ventilation. Prevent the risk of fire.

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды