MULTILIFT Ultima S Flex Скачать руководство пользователя страница 151

Страница: 151 / 196

151

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

Checking the air filter

Check the condition of the air filter. Clean and replace it as necessary.

Checking the condition of the oil

It is possible to examine ageing and deterioration of the quality of oil in the following way:

• dark colour is caused by overheating of oil

• milky and/or frothy oil contains water

• water can also be seen in separated oil

• air bubbles in oil are a sign of too little oil or of a leak in suction line

• solid particles indicate a component damage or old oil

• air is a sign of oil ageing as a result of overheating.

If you notice any of the above symptoms in oil, change it according to the following

instructions.

Attention!

Hydraulic oils, especially mineral oils, are hazardous to environment. Therefore, follow all

regulations pertaining to collecting and storing oil. Earth material polluted with oil must be

processed according to relevant instructions.

If several successive containers switches are performed, the hydraulic oil may

overheat (>60ºC) making it necessary to install an oil cooler to the system.

Either the ISO VG 22 mineral oil or the HEES ISO VG 32 biodegradable oil is used

at the factory. If biodegradable oil is used, a HEES sticker is attached to the control

valve and the oil tank.

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды