MULTILIFT Ultima S Flex Скачать руководство пользователя страница 155

Страница: 155 / 196

155

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

Safety functions

Check the safety functions of all different movements; tipping, loading and unloading. Do

the checks first without a container and thereafter with the container.

Safety functions

Check that:

• hydraulic body locks cannot be opened during tipping (tipping device approx.

20 in [0,5 m] raised)

• moving of hook arm is not possible during tipping

• hook arm cannot be moved when the hydraulic body locks are closed

• body locks signal light is lit when the locks are not closed.

Check the functioning of the load holding valves with a loaded container:

• let the hooklift stay with the container raised for 5 minutes and check that

the tipping device has not descended by itself (fig.

Tipping device

raised)

• let the hooklift stay in loading position for 5 minutes and check that the container

has not descended down (fig.

Loading position

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды