MULTILIFT Ultima S Flex Скачать руководство пользователя страница 156

Страница: 156 / 196

156

Ultima S / SL Flex & Pro

3/2019

114060421

Hooklift Multilift Ultima S / SL Flex & Pro

Service Manual

Tipping device raised

• Check the functioning of the fast speed valve (accessory) without the container. If

the valve makes an unusual noise or the movement does not seem normal, the

equipment has to be taken to maintenance and the fast speed option should not be

used before it has been checked.

• Check the functioning of the fast lowering option of the tipping device (accessory)

with an empty container and on level ground. NOTE! Fast speed might not be

activated if you are using cold oil or working on slanted ground. Never change the

settings of the sensors, as they have been calibrated separately for each

equipment.

Содержание Ultima S Flex





































































































































































































Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды

MULTILIFT Ultima S Flex, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Ultima S Flex

Отзывы:

Бренды по названию

Популярные бренды