MTU 12 V 4000 Mx4 Скачать руководство пользователя страница 60

Страница: 60 / 271

Starting (with compressed air/hydraulic starter)

Heat exchanger

engine-mounted

Heat exchanger

remote

Starting-air pressure before starter, min.

R bar

Starting-air pressure before starter, max.

R bar

Inclinations, standard oil system (reference: waterline)

Heat exchanger

engine-mounted

Heat exchanger

remote

Longitudinal inclination, continuous max.

driving end down (Option: max. operating

inclinations)

Degrees

(°)

Longitudinal inclination, temporary max.

driving end down (Option: max. operating

inclinations)

Degrees

(°)

22.5

Longitudinal inclination, continuous max.

driving end up (Option: max. operating in-

clinations)

Degrees

(°)

Transverse inclination continuous max.

(Option: max. operating inclinations)

Degrees

(°)

22.5

Capacities

Heat exchanger

engine-mounted

Heat exchanger

remote

Engine coolant, engine side (with cooling

system)

R Liters

305

Total engine oil capacity at initial filling

(standard oil system) (Option: max. oper-

ating inclinations)

R Liters

265

Oil pan capacity at dipstick mark 'min.'

(standard oil system) (Option: max. oper-

ating inclinations)

Liters

195

194

195

194

Oil pan capacity at dipstick mark 'max.'

(standard oil system) (Option: max. oper-

ating inclinations)

Liters

235

Weights / main dimensions

Heat exchanger

engine-mounted

Heat exchanger

remote

Engine dry weight (with attached standard

accessories, without coupling)

R kg

7740

7340

60 | Technical Data | MS150110/00E 2013-10

TIM-ID: 0000045624 - 001

Содержание 12 V 4000 Mx4
















































































































































































































































































Результаты поиска

Содержание 12 V 4000 Mx4

Отзывы:

Похожие инструкции для 12 V 4000 Mx4

Бренды по названию

Популярные бренды

MTU 12 V 4000 Mx4, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 4000 Mx4

Отзывы:

Похожие инструкции для 12 V 4000 Mx4

Бренды по названию

Популярные бренды