MTU 12 V 4000 Mx4 Скачать руководство пользователя страница 4

Страница: 4 / 271

7.6.2 Additional fuel filter – Replacement

190

7.6.3 Fuel filter – Replacement

191

7.6.4 Fuel system – Venting

193

7.6.5 Fuel prefilter – Differential pressure check

and adjustment of gauge

194

7.6.6 Fuel prefilter – Draining

195

7.6.7 Fuel prefilter – Flushing

197

7.6.8 Fuel prefilter with water separator – Filter

element replacement

199

7.6.9 Fuel prefilter with water separator – O-ring

replacement in rotary slide valve

201

7.7 Exhaust Turbocharger

202

7.7.1 Compressor wheel – Cleaning

202

7.8 Charge-Air Cooling

206

7.8.1 Charge-air cooler – Checking condensate drain

for water discharge and obstruction

206

7.9 Air Filter

207

7.9.1 Air filter – Replacement

207

7.9.2 Air filter – Removal and installation

208

7.10 Air Intake

209

7.10.1 Service indicator – Signal ring position check

(optional)

209

7.11 Starting Equipment

210

7.11.1 Starter – Condition check

210

7.12 Lube Oil System, Lube Oil Circuit

211

7.12.1 Engine oil – Level check

211

7.12.2 Engine oil – Change

212

7.12.3 Engine oil – Sample extraction and analysis

214

7.13 Oil Filtration / Cooling

216

7.13.1 Engine oil filter – Replacement

216

7.13.2 Automatic oil filter – Oil filter candles

replacement

218

7.13.3 Checking oil indicator filter

221

7.13.4 Centrifugal oil filter – Cleaning and filter

sleeve replacement

223

7.14 Coolant Circuit, General, High-Temperature

Circuit

226

7.14.1 Engine coolant level – Check

226

7.14.2 Engine coolant – Change

227

7.14.3 Engine coolant – Draining

228

7.14.4 Engine coolant – Filling

231

7.14.5 HT coolant pump – Relief bore check

233

7.14.6 Engine coolant – Sample extraction and

analysis

234

7.14.7 Preheating unit

235

7.15 Raw Water Pump with Connections

238

7.15.1 Raw water pump – Relief bore check

238

7.16 Battery-Charging Generator

239

7.16.1 Battery-charging generator drive – Coupling

condition check

239

7.17 Engine Mounting / Support

240

7.17.1 Engine mounting – Check

240

7.18 Auxiliary PTO

241

7.18.1 Bilge pump – Relief bore check

241

7.19 Fuel Supply System

242

7.19.1 Water drain valve – Check

242

7.19.2 Differential pressure gauge – Check

243

7.19.3 Water level probe (3-in-1 rod electrode) –

Check

244

7.19.4 Pump capacity – Check

245

7.19.5 Coalescer filter element – Replacement

246

7.20 Wiring (General) for Engine/Gearbox/Unit

248

7.20.1 Engine wiring – Check

248

7.21 Accessories for (Electronic) Engine

Governor / Control System

249

7.21.1 Resetting CDC parameter and entering IIG

with DiaSys®

249

7.21.2 Limit switch for start interlock ‒ Check

250

7.21.3 Engine Control Unit ECU 7 – Checking plug

connections

251

7.21.4 Engine Monitoring Unit EMU 8 – Plug

connections check

252

7.21.5 Interface module EIM plug connections –

Check

253

7.21.6 Engine Control Unit ECU 7 – Removal and

installation

254

7.21.7 EMU 8 – Removal and installation

255

7.21.8 Engine Interface Module EIM – Removal and

installation

256

7.21.9 Diagnostic features of EIM

257

8 Appendix A

8.1 Abbreviations

260

8.2 MTU contact persons/service partners

262

9 Appendix B

9.1 Special Tools

263

9.2 Index

269

4 | Table of Contents | MS150110/00E 2013-10

DCL-ID: 0000029807 - 001

Содержание 12 V 4000 Mx4
















































































































































































































































































Результаты поиска

Содержание 12 V 4000 Mx4

Отзывы:

Похожие инструкции для 12 V 4000 Mx4

Бренды по названию

Популярные бренды

MTU 12 V 4000 Mx4, Руководство по эксплуатации

Результаты поиска

Содержание 12 V 4000 Mx4

Отзывы:

Похожие инструкции для 12 V 4000 Mx4

Бренды по названию

Популярные бренды