18
Troubleshooting
EN
Troubleshooting
Danger
Injury hazard if engine is started inadver-
tently
Protect yourself against injury. Before carrying out
any work on this mower
-
Switch off the engine.
-Withdraw the ignition key.
-Actuate the parking brake.
-Wait until all moving parts have come to a stand-
still; the engine must have cooled down.
-
Pull the spark plug connector off the engine so
that the engine cannot inadvertently start.
Faults which occur while you are using your mower
often have simple causes which you should know
and may be able to rectify yourself. If you are in any
doubt however, your specialist workshop will be
happy to provide assistance.
Problem
Possible cause(s)
Remedy
Starter does not turn.
Safety locking system has
actuated.
To start the engine, sit on the driver’s seat,
fully depress brake pedal or apply parking
brake. Switch off the cutting mechanism.
Attach grass catcher together with dis-
charge channel or discharge flap or mulch
locking part.
Battery not connected correctly.
Connect red cable to the (+) battery termi-
nal and black cable to (–) battery terminal.
Discharged or low battery.
Charge the battery.
Fuse has tripped.
Replace fuse. If the fuse blows repeatedly,
determine the cause (usually a short-cir-
cuit).
Loose earth cable between
engine and frame.
Connect earth cable.
Starter turns but engine does not
start.
Choke and throttle in wrong
position.
Pull out choke.
Move throttle to .
Carburettor not receiving any
fuel, fuel tank empty.
Top up with fuel.
Defective or dirty
spark plug.
Check spark plug; see engine manual.
No ignition spark.
Arrange for the ignition to be checked in a
specialist workshop.
Engine producing smoke.
Too much oil in engine.
Switch the device off immediately.
Check engine oil level.
Engine defective.
Switch the device off immediately. Arrange
for a specialist workshop to check the
engine.
Strong vibrations.
Damaged blade shaft or
defective cutting blade.
Switch the device off immediately. Defec
-
tive parts must be replaced by a specialist
workshop.
Cutter deck does not discharge
grass or cuts unevenly.
Engine speed too low.
Increase throttle.
Travelling speed too high.
Set to a lower travelling speed.
Cutting blade is blunt.
Arrange for a specialist workshop to sharp-
en or replace the blade.
Engine is running; cutter deck
is not mowing.
V-belt torn.
The V-belt must be replaced in a specialist
workshop.
Содержание 13B721SD600
