manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 74

Installation

68P81096E37-N

47

06/28/05

After the station and ancillary equipment have been mechanically installed, properly cabled, and power applied, 
the equipment must then be optimized; that is, before placing the station in operation.  Optimizing is performed 
through the Radio Service Software (RSS), kit number RVN4148.

After the station is operational, the station’s codeplug data must be copied to a PC- compatible computer. 

In order to program an MTR2000 station for Trunking operation, kit 
number RVN4148C (or later) of the RSS must be used.  The current ver-
sion is available through the U.S. and Canada Americas Aftermarket Di-
vision (AAD).

Optimizing Tasks

Optimization involves the following tasks:

1.

Reading the station codeplug from the station (this ensures a match 
between the station serial number (resident in the codeplug) and the 
serial number (part of the customized station codeplug data) that is 
written back to the station (see task 5).

2.

Customizing the station codeplug and saving the data to the station

3.

Aligning the station for:

-

Rx Wireline

-

Tx  Wireline

-

Receiver RSSI calibration (option)

-

Receiver Squelch Adjust

4.

Performing post-optimization procedures.  

5.

Writing the customized codeplug to the station codeplug.

For details on these tasks, refer to the Optimizing a New Installation topic of 
the Radio Service Software (RSS) Online Help.  

Copying Station Codeplug Date To a PC-compatible Computer

A copy of each station’s codeplug data must be made on an IBM-PC 
compatible computer.  This is done through the Radio Service Software 
(RSS).  See the RSS Startup Manual, 68P81096E15.

6

OPTIMIZATION

CAUTION

!

CAUTION

!

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды