manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 73

Installation

46

68P81096E37-N

06/28/05

FailSoft

LED

This 

FailSoft

 LED indicates the following:

This LED is lit when no activity is detected on the transmit data signal 
from the trunking central controller; the station is in Failsoft mode.  This 
condition usually indicates a failed link to the trunking central controller. 

PA Keyed

LED

This 

PA Keyed

 LED indicates the following:

Listening For Audible Alarms

With a Service Speaker connected to the station (see Station Operation, 
Service Connections), any active audible alarms can be heard. 

The audible alarms are repeated every 10 seconds.  If more than one alarm 
is active, they are offset by 2 seconds.  

Exercising Radio Operation

Operation of the station radio can be verified by exercising the radio’s two-
way operation.  This may be carried out when an external speaker and mi-
crophone are connected to the Station Control Module (SCM).  

The kit # for the speaker is HSN1000.  The external speaker requires an 
adaptor cable, part # 0185180U01.

Using a speaker other than the recommended HSN1000 may result in 
the station blowing a fuse.  

The kit number for the microphone is GMN6147B.

FS

LED Color

LED State

Indicates that the …

Yellow

Flashing

station is in the Trunking system 
Failsoft mode.  

FS

LED Color

LED State

Indicates that the …

Green

On

PA is keyed.

Green

Flashing

PA is keyed, but operating with 
power cutback.

Alarm

Sound

Indicates that …

AC Fail

a single short beep

a station configured with DC-
revert has detected an AC power 
failure.

PA Fail

two short beeps

the station has been keyed, and the 
Power Amplifier has failed.

CAUTION

!

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды