manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 69

Installation

42

68P81096E37-N

06/28/05

Station Maintenance Connections

Table 12 provides a description of the maintenance connections located on 
the front of the Station Control Module.

Table 12.     Station Maintenance Connections on the SCM

Connector 

Name

Function

Details

5/10MHz 
External 
Reference Signal 
(J5603)

External 
Reference signal 
for internal 
system clock

5MHz or 10MHz external 
reference may be used.
Select desired frequency 
through RSS.  High impedance 
input. Minimum level is 1Vpp 
for either type of input.  
Maximum level should not 
exceed 3Vpp.   

Service Speaker 
(P5601)

Output to Power 
Voice speaker

Adjustable between 0 to 
500mV across 1Kohm @60% 
system deviation. Audio signal 
appears between pins 3 and 4 
on the connector. Must use 
speaker type HSN1000 via 
adapter cable Part.No. 
0185180U01.

RSS (P5600)

Serial Port

For connection to serial port of 
a computer via cable Part No. 
3082056X02.  The Radio Service 
Software (RSS) application is 
run on the computer.

Microphone 
(P5602)

Local 
Microphone 
Input

Use local microphone type 
GMN6147 or equivalent. 
Modulation sensitivity for 60% 
system deviation is typically 
300mV. This microphone 
should be equipped with 3 
control buttons for speaker 
volume control, Rx. monitor 
and Intercom control functions.

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды