Motorola MTR2000 Скачать руководство пользователя страница 59

Страница: 59 / 79

Installation

68P81096E37-N

06/28/05

System Cable Connections

System connections are made through one or both of the following connec-
tors:

the Trunking/MRTI connector and

the System connector.

Trunking/MRTI

Connector

The location of the Trunking/MRTI connector and System connector on
the station rear panel is shown in Figure 9.

The following cables are available for trunking system applications:

7.62m (25ft) Trunk Cable, part # 3083765X04

15.24m (50ft) Trunk Cable, part # 3083765X05

22.86m (75ft) Trunk Cable, part # 3083765X06

30.48m (100ft) Trunk Cable, part # 3083765X07

The following cable is available for MRTI applications:

Interface cable for Zetron model 30, kit # TTO4097

System Connector

The cable connected to the System connector can be configured for various
system options.

A generic System cable is available for variety of applications such as Wild
Card, Main Standby, and Auxiliary Input/Output:

generic System cable, kit # TKN9205A

This cable provides a housing shell for connection to the 96 pin backplane
connector, 30 loose pins, and a quantity of 30 of 24 gauge wires (2 meter
long with a pin for header on one end and unterminated at the other end).

Table 4 provides a description of commonly used System Connector pins.

Содержание MTR2000
















































































Результаты поиска

Содержание MTR2000

Отзывы:

Бренды по названию

Популярные бренды

Motorola MTR2000, Инструкция по установке и эксплуатации

Результаты поиска

Содержание MTR2000

Отзывы:

Бренды по названию

Популярные бренды