manualshive.com logo in svg

Motorola MTR2000, Инструкция по установке и эксплуатации

Поделиться
Скачать
Motorola MTR2000 Скачать руководство пользователя страница 28

68P81096E37-N

06/28/05-UP 

Motorola Inc., 2005
All Rights Reserved
Printed in U.S.A.

1301 E. Algonquin Road, Schaumburg, IL 60196

Government & Enterprise Mobility Solutions

INSTALLATION

Proper installation ensures the best possible performance and reliability of the station equipment.  Pre-installation 
planning is required.  This includes considering the mounting location of the equipment in relation to input pow-
er, antennas, and telephone interfaces.  Also to be considered are site environment conditions, the particular 
mounting method (several available), and required tools and equipment.  

If this is the first time installing this type of equipment, it is highly recommended that the user read:

•

this entire installation section before beginning the actual installation, and  

•

the Motorola Quality Standards Fixed Network Equipment Installation manual, R56  (68P81089E50); specif-
ically refer to the information on ground connection for lightning protection.

Installation Overview

The following information is an overview for installing the station and an-
cillary equipment.  Step-by-step procedures for each of the major installa-
tion tasks are then provided beginning in Section 2, Mechanical 
Installation. 

•

Plan the installation, paying particular attention to environmental 
conditions at the site, ventilation requirements, and grounding and 
lightning protection.

•

Unpack and inspect the equipment

•

Mechanically install the equipment at the site

•

If a Wireline Interface Board or an Auxiliary I/O Board is included 
with the station, configure the board jumpers for required operation

•

Make necessary electrical and cabling connections, including the fol-
lowing:
-

AC input cabling

-

Coaxial cables to transmit and receive antennas

-

Phone line connections

-

System  cables

1

PRE-INSTALLATION CONSIDERATIONS

Содержание MTR2000
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды